Phones answered 24/7Newark, OH
Call (833) 490-5225
Phones answered 24/7Call any time(833) 490-5225
Urgent? Phones answered 24/7

Flood water extraction and pumping in Newark and Licking County

Getting standing water out of a building safely and in the right order, which is the step every other part of the work waits on.

  • Phones answered 24/7
  • Licking River and storm water
  • Estimate approved before work
  • Moisture readings logged

Get a fast quote

Fastest: call (833) 490-5225. Or send this and we call you back.

Water Extraction

Flood Water Extraction and Pumping: what it covers

Quick answer

Extraction is the removal of standing and absorbed water from a building before any drying starts. Newark Water Damage Restoration answers these calls for Newark and Licking County 24/7 and dispatches a crew as fast as one is available. Pumps take the depth, extractors take what pumps cannot reach, and in a basement the level is drawn down in stages.

Flood Water Extraction and Pumping illustration for Newark, OH

Everything else on this site waits on this step. You cannot dry a building that still has water in it, you cannot assess what has to come out until you can see the floor, and you cannot clean surfaces that are submerged. Extraction is unglamorous and it is the whole hinge of a water damage job.

It is also the step where most of the water leaves. A gallon removed as liquid is a gallon a dehumidifier does not have to pull out of the air one pint at a time. Crews measure their progress here in volume, and a job where extraction was done thoroughly dries in a fraction of the time of one where it was rushed.

There is a right order to it, and it is not simply pointing a pump at the deepest spot. Power has to be dealt with first. In a flooded basement the level comes down in stages so the ground outside the wall does not win an argument with a foundation that has lost its internal support. And the water inside the carpet, the floor assembly and the wall cavity has to come out mechanically, because it will not drain to the pump on its own.

Service area
Newark & Licking County
Availability
Phones answered 24/7, emergencies first
Warning signs

Signs you need flood water extraction and pumping

Never step into standing water in a basement or crawl space while power to that level is on, and never reach through water to a switch or a panel. Do not operate a gasoline or diesel pump, or a generator, inside a basement, crawl space or closed garage: carbon monoxide builds up with no warning and kills. Keep hands and face out of contaminated water and wash thoroughly afterwards. Do not try to lift a submerged pump by its cord. If a foundation wall is bowed, cracked or leaking soil with the water, get out of the basement and do not pump it yourself.

  • Standing water of any depth on a floor, in a pit or over a slab
  • Water visible through a basement window or at the top of the stairs
  • A sump pit overflowing or a pump that runs continuously without lowering the level
  • Water rising through a floor drain instead of draining into it
  • Carpet that pushes water out around your shoe when you step on it
  • A crawl space with water over the vapor barrier or standing between piers
  • Water audibly running inside a wall or down a stairwell
  • Appliances or mechanical equipment standing in water on the lowest level
Options

Types and options for flood water extraction and pumping

A flooded basement with measurable depth

This is the job most people picture, and the one where staged pumping matters. Depth is taken down gradually, mechanical equipment on that level is assessed as it comes clear of the water, and the sump pit is checked to see whether the pump failed, was overwhelmed or lost power. Silt on the slab is cleared while damp, and the walls are read for how high the water climbed into the block.

A ground floor with water over the finished surface

Here the depth is small and the absorbed volume is large, so extraction does more work than pumping. Crews make repeated weighted passes over carpet until the tool stops producing water, lift floating floors that hold water underneath, and pull trim to reach the wall base. Doing this properly can be the difference between drying in days and drying in weeks.

A crawl space holding water over the ground

Low headroom, no drainage and a ground surface that absorbs make this the awkward one. Water is pumped from the low spots, debris and silt are cleared off the vapor barrier, and the crew works out whether the space is still taking water from saturated ground. Repeat visits are normal, because a crawl space can refill after the surface flooding has gone.

Still stuck? We pick up 24/7.

If it's an emergency, call now. For non-urgent flood water extraction and pumping, send the form and we'll call you back.

Why not just pump a flooded basement out as fast as possible?

Because the water inside is partly holding the walls in place. With saturated soil pressing from outside, removing the inside water quickly can leave a foundation wall with load on one face and nothing on the other. Staged pumping with pauses, while watching the walls, avoids turning a water loss into a structural one.

The force involved is not small. Soil that has taken on water is heavier and pushes harder than dry soil, and a basement wall is designed with the assumption that the ground is doing something predictable. During a flood, that assumption changes on both sides of the wall at once.

It is also worth knowing that pumping the basement does not stop the water arriving. If the ground is still saturated and the water table is up, the space keeps taking water through the floor and the joint where the floor meets the wall. That is why the crew looks for the source as well as the level, and why a sump system that failed gets attention before anyone declares the pumping finished.

What is the difference between pumping and extraction?

Pumping removes standing water: volume you can see and measure in inches. Extraction removes water that has been absorbed into materials, using vacuum and pressure through carpet, pad, hard flooring and cavities. A job needs both, and skipping the second is the most common reason a building takes far too long to dry.

A pump stops being useful once the water is below the level of its intake, which still leaves a building holding a great deal of water. Carpet and pad can hold a remarkable amount; so can a board subfloor, the bottom of a drywall sheet and insulation in a wall cavity. None of it flows anywhere on its own.

Where does the water go when it is pumped out?

Somewhere it will not return to the building, and somewhere appropriate for the kind of water it is. Clean storm water can often be discharged away from the foundation on the property. Water that is contaminated, or carrying sediment, is handled differently, and the right route is a question for the local authority, not a guess.

Discharge is the part of extraction that gets least thought and causes real problems. A hose run to the nearest low spot ten feet from the wall sends the water straight back through the soil into the basement, which is how a crew ends up pumping the same water twice. Distance, slope and where the ground drains all get looked at before the hose goes out.

Newark runs about 238 miles of sanitary and combined sewers with 24 lift stations, and the city promotes disconnecting downspouts from that system. In a heavy rain the last thing a combined system needs is more clean water pushed into it, which is a practical reason as well as a regulatory one for keeping storm water on the surface and away from drains where that is permitted.

What changes the scale of an extraction job?

Volume, depth, how contaminated the water is, how far the crew has to move it to discharge, the access to the wet area, and how much absorbent material is involved. It is all measured at the property, written into a scope, explained and approved before the work starts. No figure comes off a chart.

Access is usually the hidden variable. A basement with a walkout door is a different proposition from one reached by a narrow stair with a turn in it, and a crawl space hatch sets a hard limit on what equipment can get to the water. Distance from the truck to the wet area affects every hose run and every trip with a bucket.

Water type matters because it changes the method. Contaminated water means protective equipment, controlled removal of what it soaked, and cleaning before drying, so the same volume takes longer than clean water would. The categories are set out in our guide to water damage categories.

Our process

How our flood water extraction and pumping visit works

  1. Deal with the power before the water

    A technician establishes on the phone whether electrical service to the wet level can be shut off safely from a dry position. Standing water around a panel, a submerged furnace or a wet well pump are reasons to wait for the utility or a licensed electrician. No part of this job is urgent enough to justify stepping into energized water.

  2. Measure the depth and choose the equipment

    Depth, debris content and the discharge route decide what is used. Clean standing water with no solids suits a submersible pump; water carrying silt and debris needs a pump that will pass it without clogging. The crew also works out where the discharge goes, which has to be somewhere it will not run straight back to the building.

  3. Draw a deep basement down in stages

    Water inside a flooded basement is holding pressure against walls that have saturated soil pushing in from outside. Pumping it out all at once removes that balance and can crack or move a wall. The level is taken down a portion at a time with pauses, while the crew watches the walls and the floor for any sign of movement.

  4. Extract the water the pump cannot reach

    Once the depth is gone, most of the remaining water is held inside materials. Weighted extraction tools press carpet and pad to pull water out through the face, wands work hard surfaces and edges, and self-contained units handle stairs and tight corners. This is slow, repetitive work and it is where drying time is actually won.

  5. Open the places water is trapped

    Water sits behind base trim, under sheet flooring, in a wall cavity and under a stair stringer, and none of it drains out by itself. Trim comes off, weep holes are drilled low in drywall where appropriate, and floor coverings that trap water are lifted. Each opening is explained before it is made.

  6. Hand over to cleaning and drying with a record of what came out

    The crew logs the depth found, the volume removed, where the water went and what was opened. On contaminated water the cleaning stage follows immediately, and drying equipment goes in after that. The written record is what lets anyone later see why the job ran the way it did.

Licking County

Why flood water extraction and pumping is different in Central Ohio

In Newark the pattern of extraction calls follows the streams. The North Fork, South Fork and main Licking River meet here, and the USGS reports most Licking County flood damage along those three plus Raccoon Creek. That means crews are often pumping several properties in the same corridor after one rain, and water calls are taken around the clock with crews sent as they free up rather than to a promised time.

A lot of the housing stock here has a full basement or cellar under a pre-war or postwar house, which is the configuration where staged pumping and sump checks matter most. Older block and stone foundations take water into the wall itself, so after the pumping the crew reads the masonry as well as the framing. Where a sump pump failed or was overwhelmed, that gets established while the evidence is still in the pit.

Discharge choices here are shaped by the city's sewer system, which includes combined lines and lift stations and which Newark is working to separate under an Ohio EPA requirement on its 16 North project, with many pipes more than ninety years old. Putting pumped storm water back into a combined line during a storm is the opposite of helpful, so crews route discharge to the surface and away from the foundation wherever that is allowed.

Related

Licking River Flood Damage

River water pumped out, silt and soaked material removed, and the structure dried under readings after the Licking River leaves its banks.

Sump Pump Failure Water Damage

Cleanup and drying after a pump stopped, stalled or was overwhelmed, with the reason for the failure established while the evidence is still there.

Guides

Read before you book

FAQ

Flood Water Extraction and Pumping FAQs

I have a shop vacuum. Can I do this myself?

For a small clean-water spill, often yes. For a flood, a shop vacuum holds a few gallons and has no way to reach water held inside pad, subfloor or a wall cavity, so you will work for hours and still leave most of the water in the building. There is also the question of what the water is: if it came from the river, a creek or a drain, the removal is a contamination job and needs protective equipment and controlled disposal, not a vacuum and a mop.

How long does the pumping stage take?

The visible part is often quick, with depth coming out of a basement in hours rather than days. The extraction that follows takes longer and matters more, because that is the water inside materials. On a building still taking water from saturated ground, pumping may also have to be repeated over several visits. A crew will tell you after the first assessment which of those situations you are in.

Will my own sump pump handle it?

A sump pump is sized for groundwater seepage, not for a flood, and it depends on power that storms take away. When a basement has filled despite a working pump, the usual explanations are that the inflow exceeded the pump, that the discharge line was blocked or frozen, that the power went out, or that the pump had already failed quietly some weeks earlier. Which one it was is worth establishing, and it is covered on our sump pump failure page.

Do you take the carpet with you?

Only what has to go, and you will see why before it does. Pad under a flood is a loss in nearly every case. Carpet after clean water can often be dried in place after thorough extraction; after river, creek or drain water it usually comes out. Hard flooring is judged on whether water underneath can be reached without lifting it. Every removal is photographed, and what was taken is listed in the job record.

Can you pump out a crawl space that keeps refilling?

Yes, and the refilling is the thing to pay attention to. If a crawl space takes water back after pumping, the water table is up or surface water is still finding a way in, and one visit will not resolve it. The crew pumps, clears the debris and silt, and then monitors, while looking at grading, downspouts and any below-grade openings that are feeding it. Fixing the cause is a separate conversation from drying the space.

Can you work in more than one building at a property?

Yes, and on rural properties that is common, because a house, a garage and a shop may all have taken water from the same rise. Each structure gets its own assessment, because depth, construction and contents differ, and equipment is allocated where it does the most good first. The scope covers each building separately so you can see what is being done where, and it is explained and approved before work starts.

WhatsApp