Phones answered 24/7Newark, OH
Call (833) 490-5225
Phones answered 24/7Call any time(833) 490-5225
Urgent? Phones answered 24/7

Sewer backup cleanup in Newark and Licking County

Removal, cleaning and drying after waste water comes back into a building through a floor drain, toilet or laundry line.

  • Phones answered 24/7
  • Licking River and storm water
  • Estimate approved before work
  • Moisture readings logged

Get a fast quote

Fastest: call (833) 490-5225. Or send this and we call you back.

Sewer Backup

Sewer Backup Cleanup: what it covers

Quick answer

Sewer backup is the dirtiest category of water loss, so the work is removal and cleaning first and drying second. Newark Water Damage Restoration answers these calls for Newark 24/7 and sends a crew as fast as one is available. Porous material that absorbed waste water comes out, hard surfaces are cleaned and treated, and the building is then dried to readings.

Sewer Backup Cleanup illustration for Newark, OH

When a drain backs up, the lowest opening in the building becomes the relief valve for whatever is in the pipe. In most houses here that is a basement floor drain, a laundry standpipe or a basement toilet. The water that arrives has been in a sewer, which puts it in a different class from anything that comes out of a supply line, and it is handled accordingly.

Newark has a particular reason to see this. The city runs roughly 238 miles of sanitary and combined sewers served by 24 lift stations, many of the pipes more than ninety years old, and the Ohio EPA has required storm and sanitary separation on the 16 North project. In a combined sewer, storm water and waste water share a pipe, so a hard rain can fill the line that is also carrying sewage.

The practical consequence for a property owner is that this is not a mopping job. Restoration standards place sewage in the most contaminated category, which means absorbent material that took it is removed rather than dried, every hard surface it touched is cleaned and treated, and the people doing it wear protection. Doing it in the wrong order, drying first and cleaning later, spreads the problem through the building.

Service area
Newark & Licking County
Availability
Phones answered 24/7, emergencies first
Warning signs

Signs you need sewer backup cleanup

Treat sewage as an infection risk, not a mess. Stay out of the water, keep children and pets away entirely, and do not attempt the cleanup in street clothes with a mop and a bucket. Stop running water anywhere in the building, because every drain feeds the same line. Do not use bleach as a substitute for removing absorbent material, and never mix cleaning products. Food, feed and medication that contacted the water are thrown out. If the water is near electrical equipment or a furnace, leave the level alone and call (833) 490-5225 rather than switching anything on or off from a wet position.

  • Waste water standing around a basement floor drain or laundry standpipe
  • A toilet on the lowest level bubbling, or filling when nothing has been flushed
  • Several fixtures draining slowly at the same time rather than just one
  • Gurgling from a drain when a washing machine empties or a tub is released
  • A strong sewage smell on the lowest level, strongest near the drain
  • A dark tide line on the wall with solids or paper left on the floor
  • Water coming up through the drain during heavy rain and dropping again afterward
Job stories

Typical jobs for sewer backup cleanup

Typical job
Illustration: Typical: a floor drain backing up in a hard rain

Typical: a floor drain backing up in a hard rain

What homeowners notice
During heavy rain the cellar floor drain has pushed water back into the room, wetting a carpeted corner, a stack of stored boxes and the lower edge of a paneled wall.
What we do
The area is contained so it does not share air with the rest of the house, the water is extracted, the carpet, pad, paneling and wet insulation come out, hard surfaces are cleaned and disinfected, and only then is drying equipment set.
What to expect
The record shows the date, the weather at the time, the fixtures involved and everything removed, which is what the insurer and the city both ask about.

containment and cleaning first, then drying visits typical visit

Options

Types and options for sewer backup cleanup

A blockage in the building's own lateral

Roots, grease, a collapsed section or a foreign object in the pipe between the house and the main. This produces a backup with no rain involved, often building over weeks as drains run slower. Clearing the line is a plumber's job and the cleanup is ours; the two are separate trades and both have to happen, the line first so the backup does not simply resume.

A surcharged public line during heavy rain

Where storm water and sewage share a combined pipe, a hard rain can fill the main and the water finds the lowest opening in nearby buildings. This arrives at the peak of the storm, affects more than one property on a street, and goes away as the rain eases. The cleanup is the same, but the prevention conversation is about backwater protection rather than about your own pipe.

A backup that has been happening quietly

Sometimes a floor drain has been taking a little waste water for months, in a corner of a basement nobody visits. The visible water is minor and the contamination is old, which usually means more material has to come out and there is often growth on the slab, in the wall base and in whatever was stored down there. These are found by smell more often than by sight.

One call and it gets handled.

A crew is dispatched as fast as one is available, and you approve the estimate before any work starts.

Why can material not simply be cleaned and dried after a sewer backup?

Because porous material cannot be verified clean. A disinfectant has to reach a surface to work, and in carpet pad, insulation, particle board or the paper face of drywall there is no way to get it to every fiber or confirm that you did. Those materials come out; hard surfaces are cleaned and treated in place.

The standards used in this trade sort water into three categories, with sewage and river water in the most contaminated group. They also note that water starting out clean can degrade toward the next category within roughly a day to two days in a building. For sewage there is no such clock, because it starts at the far end.

Why does a hard rain cause sewage to come back into a basement?

In a combined sewer, storm water and waste water travel in the same pipe. When rain fills that pipe faster than it can discharge, the line surcharges and the water seeks the lowest opening, which is often a basement floor drain. Newark has about 238 miles of sanitary and combined sewers and is separating storm from sanitary under an Ohio EPA requirement.

Combined systems were a sensible nineteenth and early twentieth century design and they are now a known problem everywhere they exist. Newark has pipes more than ninety years old in service, 24 lift stations moving flow around the system, and the 16 North separation project required by the Ohio EPA. The city also promotes disconnecting downspouts, which keeps roof water out of the combined line.

What has to be thrown out, and what can be kept?

Hard, non-absorbent items can usually be cleaned and kept: metal, glazed ceramic, sealed concrete, solid wood that can be cleaned on every face, and glass. Absorbent items generally go: carpet pad, mattresses, upholstered furniture, cardboard, particle board, insulation and drywall that was in the water.

The question to ask about any object is whether a cleaning agent can reach every surface that the water reached, and whether you could tell afterwards. A steel shelving unit passes that test easily. A pressed-wood bookcase does not, because the water goes into the edges and the core and never comes out.

Sentimental items are their own category and worth raising early. Photographs, documents and some textiles can sometimes be handled by specialist cleaning rather than discarded, and the decision is better made at the start than after they have sat in a bag for a week. Tell the crew what matters to you before the removal begins.

  • Keep and clean: metal shelving, glazed tile, glass, sealed concrete, solid hardwood furniture
  • Remove: carpet pad, wet insulation, particle board, cardboard, mattresses, upholstery
  • Discard any food, feed or medication that contacted the water or was stored in it
  • Set aside photographs and documents for specialist handling rather than binning them
  • Wash clothing that was in the water separately and on the hottest cycle the fabric allows

What moves the scope of a sewer backup job up or down?

How far the water spread, how much of what it touched was absorbent, whether the space is finished, how long it sat, and how reachable the area is for containment and equipment. It is all measured at the property and written into a scope that is explained and approved before work starts.

Containment makes this job unlike a clean-water loss. Setting a work zone, running negative air and protecting routes through the house all take time and material, and they are not optional on a category three loss. An area with its own exterior door is quicker to contain than a basement reached through the middle of a finished house.

Finish level then decides volume of removal. An unfinished basement with a slab and block walls may lose nothing but the stored contents on the floor. A finished basement puts carpet, pad, drywall, insulation, trim and cabinetry in contact with waste water, and most of the lower band of all of it comes out.

Is a sewer backup covered by insurance?

Standard homeowners policies generally exclude water that backs up through drains, sewers and sump pumps, and a water backup endorsement is the usual way to cover it. Limits and conditions vary by policy. Ask your agent what your own declarations page says rather than assuming either answer.

The exclusion is a common surprise and it is worth understanding before you need it. It is also not confined to homes: the Ohio Supreme Court held, by a five to two majority, that sewage fell under a water exclusion in a commercial policy in a case involving an Akron nightclub. Commercial cover deserves the same reading.

Whatever your policy says, the documentation is the same. Dated photographs before anything moves, the depth and extent recorded, an itemized list of what was removed and why, and a moisture log through the drying are what an adjuster works from. No restoration crew can promise an outcome on a claim. Our sewer backup guide for Newark covers who to call in what order.

Our process

How our sewer backup cleanup visit works

  1. Stop adding to it

    The first instruction on the phone is to stop using water in the building: no toilets, no laundry, no showers, no dishwasher. Everything that goes down a drain is going to the same blocked or surcharged line and will come back into the same room. A technician will also ask whether the backup is still rising.

  2. Contain the area before anything is carried through the house

    Plastic containment and a negative air machine keep the affected area under slightly lower pressure than the rest of the building, so air and odor move into the work zone rather than out of it. Pathways are protected. This is what stops a basement problem becoming a whole-house problem during the cleanup.

  3. Remove the water and the solids

    Extraction equipment suited to contaminated water takes out the standing water and what is in it. Solids are collected and bagged as they are found rather than pushed around with a squeegee. The crew records depth, extent and what the water reached, which matters later for both the repair and any claim.

  4. Take out everything porous that it touched

    Carpet and pad, soaked drywall and insulation, particle board, stored cardboard, upholstered furniture that absorbed it and any wood product that cannot be cleaned on all faces come out. Drywall is cut a clear margin above the high-water line. Nothing porous that held sewage is dried in place and kept.

  5. Clean, then treat, every hard surface

    Slab, masonry, framing, joists, pipes, duct exteriors and the undersides of everything in the zone are cleaned and then treated with an antimicrobial. The cleaning is the part that does the work; the treatment is applied to surfaces that are already clean, because a disinfectant sprayed over soil does very little.

  6. Dry the structure and verify

    Only once the area is clean do air movers and dehumidifiers go in, so the airflow is moving through a cleaned space. Readings in framing, slab and masonry are taken on each visit until they hold at target. Rebuilding is quoted separately, after the structure is confirmed dry and the scope has been explained and approved.

Licking County

Why sewer backup cleanup is different in Central Ohio

The age and type of the system here explain the pattern of calls. Newark operates about 238 miles of sanitary and combined sewers with 24 lift stations, with many pipes more than ninety years old, and the Ohio EPA has required storm and sanitary separation on the 16 North project. Where storm and waste water still share a pipe, a heavy rain is a sewer event as well as a flood event, and the two arrive on the same night.

The housing stock puts a lot of drains in basements. Newark has a mix of pre-war and postwar houses, and in that era a floor drain, a laundry standpipe and sometimes a toilet all sat on the lowest level, which is exactly where a surcharged line finds its opening. Older clay and cast laterals under mature trees add root intrusion as a second, rain-independent cause.

Rain of the scale that fills these pipes is on the record here. More than four inches fell across the county in under forty-eight hours on April 2, 2024, and the city's own advice to disconnect downspouts from the sewer system is aimed squarely at reducing what arrives in the pipe during storms like it. Properties in the older, lower parts of town feel this first, since the lowest opening in the lowest building is where the line relieves itself.

Related

Flood Water Extraction and Pumping

Getting standing water out of a building safely and in the right order, which is the step every other part of the work waits on.

Mold After Water Damage

Containment, removal, cleaning and drying where growth has established after a leak, a flood or a long-running damp problem.

Guides

Read before you book

FAQ

Sewer Backup Cleanup FAQs

Do I need a plumber or a restoration crew?

Usually both, and in that order where the blockage is in your own line. A plumber clears or repairs the pipe so the backup stops; the restoration work removes the contaminated material, cleans and treats the surfaces and dries the structure. Cleaning up before the line is clear risks doing it twice. Where the cause is a surcharged public main in a storm, there may be nothing in your own pipe to fix and the cleanup can start as soon as the water drops.

Can I clean it up myself with bleach?

Bleach on a hard surface that has already been cleaned has a role. Bleach sprayed over soil, or onto carpet pad and drywall, does not solve the problem: it cannot reach into porous material, it does not remove what is there, and it leaves you with wet contaminated material that now also smells of chlorine. The removal of absorbent material and the physical cleaning of surfaces are what make a space safe, and they need protective equipment to do.

How long does the cleanup take?

The removal and cleaning stage is usually the shorter part, often a day or so in a typical basement, and the drying that follows runs on readings rather than a schedule. Equipment stays until framing, slab and masonry hold at target. Containment comes down when the cleaning is verified and the area is dry. You will know the expected shape of it after the first assessment, and the moisture log is available to you throughout.

Will the smell go away?

Yes, if the source is actually removed. A sewage smell that lingers after cleanup almost always means absorbent material was left in place, a cavity was not opened, or something is still wet. Deodorizing an area that still contains the source masks it for a few days. The correct response is to go back with a meter and a light, find what is holding it, and take that out, which is why the removal decisions are made deliberately at the start.

Can this be prevented?

Partly, and it depends on the cause. Where your own lateral blocks, keeping grease out of drains and having a line with root intrusion inspected and cleared helps. Where the public line surcharges in storms, protection at the building, such as a backwater device, is the relevant measure, and that is a licensed plumber's decision rather than a restoration one. Keeping roof water out of a combined sewer by disconnecting downspouts, as Newark promotes, reduces what has to move through the pipe in a storm.

Does the furnace or water heater need looking at afterwards?

If either was standing in the water, yes, and not by us. Burners, controls, gas valves and electrical components that were submerged in waste water are a licensed trade’s decision, and the honest answer on restarting them is that nobody should until that trade has cleared them. Duct work that filled is a separate question again, because the inside of a duct run cannot be cleaned by spraying the outside of it.

WhatsApp